FUEGO 32EL610ANDT TP.MT5510S.PB803 EMMC Firmware Download
![fuego 32EL610ANDT](https://repairalltv.com/wp-content/uploads/2021/02/fuego-32EL610ANDT.jpg)
fuego 32el610andt tp.mt5510S.pb803 emmc Firmware Download
tp.mt5510S.pb803 emmc Firmware
TV MODEL 32EL610ANDT
![TP.MT5510S.PB803 EMMC Firmware](https://repairalltv.com/wp-content/uploads/2021/02/TP.MT5510S.PB803-300x169.jpg)
BOARD TP.MT5510S.PB803
FUEGO 32EL610ANDT TP.MT5510S.PB803 EMMC Firmware Download
![ISP PIN KLM8G1GETF B041.](https://repairalltv.com/wp-content/uploads/2021/02/ISP-PIN-KLM8G1GETF-B041.-300x169.jpg)
READ EMMC PROGRAMMER TNM5000
![there is no need EMMC for extras for 3.3v nor for 1.8v if you combine two crystal 24.000 pins with GND. and insert the board at 220V in. plug](https://repairalltv.com/wp-content/uploads/2021/02/there-is-no-need-EMMC-for-extras-for-3.3v-nor-for-1.8v-if-you-combine-two-crystal-24.000-pins-with-GND.-and-insert-the-board-at-220V-in.-plug-300x169.jpg)
option 2. as in the picture read Emmc
![ISP PIN READ EMMC TNM 5000](https://repairalltv.com/wp-content/uploads/2020/10/pin-isp-wire-EMMC-read-all-300x146.png)
isp pinout info
![ISP CABLE EMMC PIN](https://repairalltv.com/wp-content/uploads/2020/10/ISP-CABLE-EMMC-PIN-300x150.png)
Programmer ISP Cable EMMC pin
ISP PIN 1 CMD
ISP PIN 3 RST-n(Reset) (mandatory)
ISP PIN 5 CLK (Clock)
ISP PIN 6 DAT0
ISP PIN 8, 10 VSS (GND)
Vcc of Chip Must be ON. Reset is needed only when circuit reset is not working.
Note 1: After Selecting EMMC, programmer will be switched to Report view.
because EMMC files are too large and can’t be viewed by hex editor.
you can switch back to hex editor by unmarking the report button.
Note 2: Load & Save buttons has no use in EMMC nand. you must select filename
after pressing read or program buttons. File will be saved automatically with
.Boot 1, .Boot 2, RPMB, EXT_CSD extensions for different parts of the chip.
Note 3: After pressing read or Program, EMMC size and type will automatically
be Detected.
Note 4: Use Config Window for selecting Different Parts of the chip for read and write.
Also, chip Size and name is read from the chip and can be viewed in this window.
Note 5: Erase is for total chip erase. before Programming Each part, Programmer
will erase it automatically, so no need for chip erase before program.
Note 6: Only First 192 byte of EXT_CSD is writable by users and Some of these bytes
are read-only and some parts are one-time programable so if you write over these areas,
you get Write error.
Note 7: in most cases, Reset Pin is not necessory, Power on/off the device for reset
![RT809H PROGRAMMER ISP INFO.](https://repairalltv.com/wp-content/uploads/2021/02/RT809H-PROGRAMMER-ISP-INFO.-300x169.jpg)
RT809H PROGRAMMER ISP INFO
![there is no need EMMC for extras for 3.3v nor for 1.8v if you combine two crystal 24.000 pins with GND. and insert the board at 220V in. plug](https://repairalltv.com/wp-content/uploads/2021/02/there-is-no-need-EMMC-for-extras-for-3.3v-nor-for-1.8v-if-you-combine-two-crystal-24.000-pins-with-GND.-and-insert-the-board-at-220V-in.-plug-300x169.jpg)
☝☝
option 2. as in the picture read Emmc
![CX315DLEDM LE 32P28](https://repairalltv.com/wp-content/uploads/2021/02/CX315DLEDM-LE-32P28-300x169.jpg)
CX315DLEDM LE-32P28
![ST3151A07 1 XC 3](https://repairalltv.com/wp-content/uploads/2021/02/ST3151A07-1-XC-3-300x169.jpg)
BOARD SCREEN ST3151A07-1-XC-3
![SMART TV](https://repairalltv.com/wp-content/uploads/2021/02/SMART-TV-300x169.jpg)
SMART TV android
My channel YouTube👉 RepairAllTV