SUNNY SN40DIL13/0216 HK.T.RT2841P631 18AT013 EMMC Firmware

sunny sn40dil13/0216 hk.t.rt2841p631 18at013 EMMC Firmware SUNNY SN40DIL13/0216 HK.T.RT2841P631 18AT013 EMMC Firmware

TV MODEL sn40dil13/0216

BOARD TV SUNNY

sunny sn40dil13/0216 hk.t.rt2841p631 18at013 EMMC Firmware

BOARD TV

PROGRAMMER TNM5000 ISP READ EMMC H26M41204HPR

crystal 27.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

TNM5000 ISP READ EMMC

ISP INFO READ EMMC PROGRAMMER TNM5000 READ EMMC BOARD hk.t.rt2841p631 18at013

Programmer ISP Cable EMMC pin
ISP PIN 1 CMD
ISP PIN 3 RST-n(Reset) (mandatory)
ISP PIN 5 CLK (Clock)
ISP PIN 6 DAT0
ISP PIN 8, 10 VSS (GND)
Vcc of Chip Must be ON. Reset is needed only when circuit reset is not working.

Note 1: After Selecting EMMC, programmer will be switched to Report view.
because EMMC files are too large and can’t be viewed by hex editor.
you can switch back to hex editor by unmarking the report button.

Note 2: Load & Save buttons has no use in EMMC nand. you must select filename
after pressing read or program buttons. File will be saved automatically with
Boot 1, Boot 2, RPMB, EXT_CSD extensions for different parts of the chip.

Note 3: After pressing read or Program, EMMC size and type will automatically
be Detected

Note 4 : Use Config Window for selecting Different Parts of the chip for read and write.
Also, chip Size and name is read from the chip and can be viewed in this window.

Note 5: Erase is for total chip erase. before Programming Each part, Programmer
will erase it automatically, so no need for chip erase before program.

Note 6: Only First 192 byte of EXT_CSD is writable by users and Some of these bytes
are read-only and some parts are one-time programable so if you write over these areas,
you get Write error.

Note 7: in most cases, Reset Pin is not necessory, Power on/off the device for reset

PROGRAMMER RT809H PIN ISP READ EMMC H26M41204HPR

crystal 27.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

MODEL PANEL LSC400HN02-804

ANDROID TV

TV OK

My channel YouTube RepairAllTV

DUMP EMMC NAND EEPROM
Important notes: The files we make available on this website are backup copies of device firmware that were fully operational at the time of copying.
We always try to refer to the technical data of the device, however we inform you that there may be some incompatibility with your device, even if it is the same model.
Firmware is generally fully compatible, but users should be aware that there is a possibility of incompatibility.

You need an programmer to write this dump to the chip.
Please remember to back up your firmware to restore in case of any errors or incompatibilities.

HK.T.RT2841P631 18AT013 EMMC Firmware

EMMC SUNNY 40 Firmware part1

1 file(s) 692 MB

Please (log in)

EMMC SUNNY 40 Firmware part2

1 file(s) 2 MB

Please (log in)

download only eeprom or dump or nand flash EMMC. here Subscription

Subscription more here (Select subscription plan)