FUEGO 43EL610ANDT P75-2841V6.0 EMMC THGBMFG6C1LBAIL
May 17, 2021
![FUEGO 43EL610ANDT](https://repairalltv.com/wp-content/uploads/2021/05/FUEGO-43EL610ANDT.jpg)
fuego 43el610andt p75-2841v6.0 emmc thgbmfg6c1lbail
![BOARD TV 2](https://repairalltv.com/wp-content/uploads/2021/05/BOARD-TV-2-300x169.jpg)
BOARD TV
![BOARD MODEL P75 2841V6.0](https://repairalltv.com/wp-content/uploads/2021/05/BOARD-MODEL-P75-2841V6.0-300x169.jpg)
BOARD MODEL P75-2841V6.0
![BOARD MODEL](https://repairalltv.com/wp-content/uploads/2021/05/BOARD-MODEL-300x169.jpg)
BOARD MODEL
![EMMC](https://repairalltv.com/wp-content/uploads/2021/05/EMMC-300x169.jpg)
EMMC
![READ EMMC PROGRAMMER TNM 5000](https://repairalltv.com/wp-content/uploads/2021/05/READ-EMMC-PROGRAMMER-TNM-5000-300x169.jpg)
READ EMMC PROGRAMMER TNM5000
![BOARD CV6681H A42 crystal 27.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC 1](https://repairalltv.com/wp-content/uploads/2021/05/BOARD-CV6681H-A42-crystal-27.000-MHz-PINS-1-and-2-connect-with-GND.-tv-must-be-in-220v-plug.-and-read-EMMC.-no-need-for-extra-voltage.-3.3v-and-1.8v.-for-reading-EMMC-1-300x169.jpg)
BOARD P75-2841V6.0 crystal 27.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC
![ISP PIN READ EMMC TNM 5000](https://repairalltv.com/wp-content/uploads/2020/10/pin-isp-wire-EMMC-read-all-300x146.png)
ISP PIN READ EMMC TNM 5000
![ISP CABLE EMMC PIN](https://repairalltv.com/wp-content/uploads/2020/10/ISP-CABLE-EMMC-PIN-300x150.png)
ISP INFO READ EMMC PROGRAMMER TNM5000 READ EMMC BOARD P75-2841V6.0
Programmer ISP Cable EMMC pin
ISP PIN 1 CMD
ISP PIN 3 RST-n(Reset) (mandatory)
ISP PIN 5 CLK (Clock)
ISP PIN 6 DAT0
ISP PIN 8, 10 VSS (GND)
Vcc of Chip Must be ON. Reset is needed only when circuit reset is not working.
Note 1: After Selecting EMMC, programmer will be switched to Report view.
because EMMC files are too large and can’t be viewed by hex editor.
you can switch back to hex editor by unmarking the report button.
Note 2: Load & Save buttons has no use in EMMC nand. you must select filename
after pressing read or program buttons. File will be saved automatically with
Boot 1, Boot 2, RPMB, EXT_CSD extensions for different parts of the chip.
Note 3: After pressing read or Program, EMMC size and type will automatically
be Detected
Note 4 : Use Config Window for selecting Different Parts of the chip for read and write.
Also, chip Size and name is read from the chip and can be viewed in this window.
Note 5: Erase is for total chip erase. before Programming Each part, Programmer
will erase it automatically, so no need for chip erase before program.
Note 6: Only First 192 byte of EXT_CSD is writable by users and Some of these bytes
are read-only and some parts are one-time programable so if you write over these areas,
you get Write error.
Note 7: in most cases, Reset Pin is not necessory, Power on/off the device for reset
![READ EMMC ISP PROGRAMMER RT809.H](https://repairalltv.com/wp-content/uploads/2021/05/READ-EMMC-ISP-PROGRAMMER-RT809.H-300x169.jpg)
READ EMMC ISP PROGRAMMER RT809H
![BOARD CV6681H A42 crystal 27.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC 1](https://repairalltv.com/wp-content/uploads/2021/05/BOARD-CV6681H-A42-crystal-27.000-MHz-PINS-1-and-2-connect-with-GND.-tv-must-be-in-220v-plug.-and-read-EMMC.-no-need-for-extra-voltage.-3.3v-and-1.8v.-for-reading-EMMC-1-300x169.jpg)
BOARD P75-2841V6.0 crystal 27.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC
![PANEL CX430DLEDM](https://repairalltv.com/wp-content/uploads/2021/05/PANEL-CX430DLEDM-300x169.jpg)
PANEL MODEL CX430DLEDM
THGBMFG6C1LBAILISP Bin Firmware
1 file(s) 1 GB
downloads are by subscription
Please (Subscription, for download)