FUEGO 50ELU610ANDT TP.MT5522S.PC822 EMMC BIN FIRMWARE

June 16, 2021
FUEGO 50ELU610ANDT
Share post with Friends

fuego 50elu610andt tp.mt5522s.pc822 emmc bin firmware

to download, you must subscribe 👉 Subscription, for download or RepairAllTV Subscriptions 1 to 10

BOARD TV T CON BOARD

BOARD TV T-CON BOARD

MODEL BOARD TP.MT5522S.PC822

MODEL BOARD TP.MT5522S.PC822

EMMC BIN FIRMWARE

EMMC BIN FIRMWARE

emmc pinout 1

emmc pinout

BOARD TP.MT5522S.PC822 crystal 24.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

BOARD TP.MT5522S.PC822 crystal 24.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

READ EMMC pinout PROGRAMMER TNM 5000

READ EMMC pinout PROGRAMMER TNM 5000

ISP PIN READ EMMC TNM 5000

emmc pinout ISP PROGRAMMER TNM5000

ISP CABLE EMMC PIN

ISP INFO READ EMMC PROGRAMMER TNM5000 READ EMMC

Programmer ISP Cable EMMC pin
ISP PIN 1 CMD
ISP PIN 3 RST-n(Reset) (mandatory)
ISP PIN 5 CLK (Clock)
ISP PIN 6 DAT0
ISP PIN 8, 10 VSS (GND)
Vcc of Chip Must be ON. Reset is needed only when circuit reset is not working.

Note 1: After Selecting EMMC, programmer will be switched to Report view.
because EMMC files are too large and can’t be viewed by hex editor.
you can switch back to hex editor by unmarking the report button
.

Note 2: Load & Save buttons has no use in EMMC nand. you must select filename
after pressing read or program buttons. File will be saved automatically with
Boot 1, Boot 2, RPMB, EXT_CSD extensions for different parts of the chip.

Note 3: After pressing read or Program, EMMC size and type will automatically
be Detected

Note 4Use Config Window for selecting Different Parts of the chip for read and write.
Also, chip Size and name is read from the chip and can be viewed in this window.

Note 5: Erase is for total chip erase. before Programming Each part, Programmer
will erase it automatically, so no need for chip erase before program.




Note 6: Only First 192 byte of EXT_CSD is writable by users and Some of these bytes
are read-only and some parts are one-time programable so if you write over these areas,
you get Write error.

Note 7: in most cases, Reset Pin is not necessory, Power on/off the device for reset


BOARD TP.MT5522S.PC822 crystal 24.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

BOARD TP.MT5522S.PC822 crystal 24.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

RT809H READ EMMC pinout

RT809H READ EMMC pinout

MODEL PANEL CX500DLEDM

MODEL PANEL CX500DLEDM



repairalltv.com