GRUNDIG 49GUB9890 ZGF190R-6 EMMC BIN FIRMWARE Download
![GRUNDIG 49GUB9890](https://repairalltv.com/wp-content/uploads/2021/03/GRUNDIG-49GUB9890.jpg)
grundig 49gub9890 zgf190r-6 emmc bin firmware Download
![TV GRUNDIG](https://repairalltv.com/wp-content/uploads/2021/03/TV-GRUNDIG-300x169.jpg)
![MAIN BOARD](https://repairalltv.com/wp-content/uploads/2021/03/MAIN-BOARD-300x169.jpg)
GRUNDIG MAIN BOARD
grundig 49gub9890 zgf190r-6 emmc bin firmware Download
![MAIN BOARD ZGF190R 6](https://repairalltv.com/wp-content/uploads/2021/03/MAIN-BOARD-ZGF190R-6-300x169.jpg)
MAIN BOARD ZGF190R-6
![GF PYN2ZZ](https://repairalltv.com/wp-content/uploads/2021/03/GF-PYN2ZZ-300x169.jpg)
GF PYN2ZZ
![EMMC](https://repairalltv.com/wp-content/uploads/2021/03/EMMC-300x169.jpg)
![active power board in plug 220v. connects the power board cable to the mainboard. then read EMMC.........](https://repairalltv.com/wp-content/uploads/2021/03/active-power-board-in-plug-220v.-connects-the-power-board-cable-to-the-mainboard.-then-read-EMMC.........-300x169.jpg)
(active power board in plug 220v). connects the power board cable to the mainboard. then read EMMC
![PROGRAMMER TNM500 SPI INFO 2](https://repairalltv.com/wp-content/uploads/2021/03/PROGRAMMER-TNM500-SPI-INFO-2-300x169.jpg)
PROGRAMMER TNM500 SPI INFO THGBMDG5D1LBAIL
![READ EMMC 3776 MB](https://repairalltv.com/wp-content/uploads/2021/03/READ-EMMC-3776-MB-300x201.jpg)
READ EMMC 3776MB
![ISP PIN READ EMMC TNM 5000](https://repairalltv.com/wp-content/uploads/2020/10/pin-isp-wire-EMMC-read-all-300x146.png)
EMMC ISP INFO
![ISP CABLE EMMC PIN](https://repairalltv.com/wp-content/uploads/2020/10/ISP-CABLE-EMMC-PIN-300x150.png)
ISP INFO READ EMMC PROGRAMMER TNM5000 READ EMMC BOARD MAIN BOARD ZGF190R-6
Programmer ISP Cable EMMC pin
ISP PIN 1 CMD
ISP PIN 3 RST-n(Reset) (mandatory)
ISP PIN 5 CLK (Clock)
ISP PIN 6 DAT0
ISP PIN 8, 10 VSS (GND)
Vcc of Chip Must be ON. Reset is needed only when circuit reset is not working.
Note 1 : After Selecting EMMC, programmer will be switched to Report view.
because EMMC files are too large and can’t be viewed by hex editor.
you can switch back to hex editor by unmarking the report button.
Note 2: Load & Save buttons has no use in EMMC nand. you must select filename
after pressing read or program buttons. File will be saved automatically with
Boot 1, Boot 2, RPMB, EXT_CSD extensions for different parts of the chip.
Note 3: After pressing read or Program, EMMC size and type will automatically
be Detected.
Note 4: Use Config Window for selecting Different Parts of the chip for read and write.
Also, chip Size and name is read from the chip and can be viewed in this window.
Note 5: Erase is for total chip erase. before Programming Each part, Programmer
will erase it automatically, so no need for chip erase before program.
Note 6: Only First 192 byte of EXT_CSD is writable by users and Some of these bytes
are read-only and some parts are one-time programable so if you write over these areas,
you get Write error.
Note 7 : in most cases, Reset Pin is not necessory, Power on/off the device for reset
![PROGRAMMER RT809H ISP 2](https://repairalltv.com/wp-content/uploads/2021/03/PROGRAMMER-RT809H-ISP-2-300x169.jpg)
PROGRAMMER RT809H ISP THGBMDG5D1LBAIL
![ISP PROGRAMMER RT809H](https://repairalltv.com/wp-content/uploads/2021/01/ISP-PROGRAMMER-RT809H-300x248.jpg)
PROGRAMMER RT809H ISP
![25Q32 BIN DUMP](https://repairalltv.com/wp-content/uploads/2021/03/25Q32-BIN-DUMP-300x169.jpg)
25Q32 BIN DUMP