Panasonic TX-55CRW434 17MB100 EMMC BIN Firmware Curved TV

May 24, 2021
Panasonic TX 55CRW434
Share post with Friends

PANASONIC tx-55crw434 17mb100 emmc bin Firmware Curved TV

MAIN BOARD POWER BOARD T CON BOARD

MAIN BOARD POWER BOARD T-CON BOARD

MAIN BOARD

MAIN BOARD

MAIN BOARD 17MB100 VESTEL

MAIN BOARD 17MB100 VESTEL

BOARD

BOARD

H26M31001HPR IMAGE

H26M31001HPR FIRMWARE

EMMC REMOVE

REMOVE EMMC pinout

to see EMMC pinout photo as well as to download EMMC BIN Firmware. you must subscribe

READ EMMC ISP PROGRAMMER TNM5000

READ EMMC ISP PROGRAMMER TNM5000

POWER BOARD. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

POWER BOARD. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

BOARD 17MB100 crystal 24.515 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

BOARD 17MB100 crystal 24.515 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

ISP PIN READ EMMC TNM 5000

ISP PIN READ EMMC TNM 5000

ISP CABLE EMMC PIN

ISP INFO READ EMMC PROGRAMMER TNM5000 READ EMMC BOARD 17MB100 VESTEL

Programmer ISP Cable EMMC pin
ISP PIN 1 CMD
ISP PIN 3 RST-n(Reset) (mandatory)
ISP PIN 5 CLK (Clock)
ISP PIN 6 DAT0
ISP PIN 8, 10 VSS (GND)
Vcc of Chip Must be ON. Reset is needed only when circuit reset is not working.

Note 1: After Selecting EMMC, programmer will be switched to Report view.
because EMMC files are too large and can’t be viewed by hex editor.
you can switch back to hex editor by unmarking the report button
.

Note 2: Load & Save buttons has no use in EMMC nand. you must select filename
after pressing read or program buttons. File will be saved automatically with
Boot 1, Boot 2, RPMB, EXT_CSD extensions for different parts of the chip.

Note 3: After pressing read or Program, EMMC size and type will automatically
be Detected

Note 4 : Use Config Window for selecting Different Parts of the chip for read and write.
Also, chip Size and name is read from the chip and can be viewed in this window.

Note 5: Erase is for total chip erase. before Programming Each part, Programmer
will erase it automatically, so no need for chip erase before program.

Note 6: Only First 192 byte of EXT_CSD is writable by users and Some of these bytes
are read-only and some parts are one-time programable so if you write over these areas,
you get Write error.

Note 7: in most cases, Reset Pin is not necessory, Power on/off the device for reset


to see EMMC pinout photo as well as to download EMMC BIN Firmware. you must subscribe

ISP PROGRAMMER RT809H

ISP PROGRAMMER RT809H

BOARD 17MB100 crystal 24.515 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

POWER BOARD. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

POWER BOARD. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

MODEL PANEL LTA550FW01

MODEL PANEL LTA550FW01

25L1606E U27

25L1606E (U27)

25L1606E U26

25L1606E (U26)

25Q32F U25

25Q32F (U25)



repairalltv.com