SHARP 42CG3E TP.MS6486X.PB713 EMMC FIRMWARE
![SHARP 42CG3E](https://repairalltv.com/wp-content/uploads/2023/08/SHARP-42CG3E.jpg)
sharp 42cg3e tp.ms6486x.pb713 emmc firmware download
![SHARP EMMC](https://repairalltv.com/wp-content/uploads/2023/08/SHARP-EMMC-300x169.jpg)
tp.ms6486x.pb713 emmc firmware
![TP.MS6486X.PB713 EMMC FIRMWARE](https://repairalltv.com/wp-content/uploads/2023/08/BOARD-TP.MS6486X.PB713-300x169.jpg)
BOARD TP.MS6486X.PB713
![KLM4G1FETE B041 FIRMWARE](https://repairalltv.com/wp-content/uploads/2023/08/KLM4G1FETE-B041-FIRMWARE-300x169.jpg)
KLM4G1FETE-B041 FIRMWARE
![TNM5000 ISP EMMC READ HIDE](https://repairalltv.com/wp-content/uploads/2023/08/TNM5000-ISP-EMMC-READ-HIDE-300x169.jpg)
to see EMMC pinout photo as well as to download EMMC BIN Firmware. you must subscribe
TNM5000 ISP READ EMMC
![ISP PIN READ EMMC TNM 5000](https://repairalltv.com/wp-content/uploads/2020/10/pin-isp-wire-EMMC-read-all-300x146.png)
EMMC ISP PROGRAMMER TNM5000
![ISP CABLE EMMC PIN](https://repairalltv.com/wp-content/uploads/2020/10/ISP-CABLE-EMMC-PIN-300x150.png)
Programmer ISP Cable EMMC pin
ISP PIN 1 CMD
ISP PIN 3 RST-n(Reset) (mandatory)
ISP PIN 5 CLK (Clock)
ISP PIN 6 DAT0
ISP PIN 8,10 VSS (GND)
Vcc of Chip Must be ON. Reset is needed only when circuit reset is not working
Note 1: After Selecting EMMC, programmer will be switched to Report view.
because EMMC files are too large and can’t be viewed by hex editor.
you can switch back to hex editor by unmarking the report button.
Note 2: Load & Save buttons has no use in EMMC nand. you must select filename
after pressing read or program buttons. File will be saved automatically with
Boot1, Boot2, RPMB, EXT_CSD extensions for different parts of the chip.
Note 3: After pressing read or Program, EMMC size and type will automatically
be Detected.
Note 4: Use Config Window for selecting Different Parts of the chip for read and write.
Also, chip Size and name is read from the chip and can be viewed in this window.
Note 5: Erase is for total chip erase. before Programming Each part, Programmer
will erase it automatically, so no need for chip erase before program.
Note 6: Only First 192 byte of EXT_CSD is writable by users and Some of these bytes
are read-only and some parts are one-time programable so if you write over these areas,
you get Write error.
Note 7: in most cases, Reset Pin is not necessory, Power on/off the device for reset
![XGecu T56](https://repairalltv.com/wp-content/uploads/2023/08/XGecu-T56-300x169.jpg)
XGecu T56
![READ EMMC RT809H ISP HIDE](https://repairalltv.com/wp-content/uploads/2023/08/READ-EMMC-RT809H-ISP-HIDE-300x169.jpg)
READ EMMC RT809H ISP
to see EMMC pinout photo as well as to download EMMC BIN Firmware. you must subscribe
![PANEL JE415D3HA00](https://repairalltv.com/wp-content/uploads/2023/08/PANEL-JE415D3HA00-300x169.jpg)
PANEL JE415D3HA00
My channel YouTube👉 RepairAllTV
SHARP MODEL 42CG3E
BOARD TP.MS6486X.PB713
EMMC KLM4G1FETE-B041 Size: 3.8GB
PANEL JE415D3HA00
READ EMMC PROGRAMMER TNM5000, READ EMMC PROGRAMMER XGecu T56