SUNNY SN49DLK27-0216 HK.T.RT2841P831 18AT027 EMMC

January 10, 2022
SUNNY SN49DLK27 0216
Share post with Friends

sunny sn49dlk27-0216 hk.t.rt2841p831 18at027 emmc SN49DLK27-0216 HK.T.RT2841P831 18AT027 EMMC

MAIN BOARD

board sunny 49

BOARD HK.T.RT2841P831 SUNNY 18AT027

BOARD HK.T.RT2841P831 SUNNY 18AT027

SN49DLK27-0216 HK.T.RT2841P831 18AT027 EMMC

READ EMMC

to see EMMC pinout photo as well as to download EMMC BIN Firmware. you must subscribe

PROGRAMMER TNM5000 ISP READ EMMC

PROGRAMMER TNM5000 ISP READ EMMC H26M41204HPR

crystal 27.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC 1

crystal 27.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

ISP PIN READ EMMC TNM 5000

TNM5000 ISP READ EMMC

ISP CABLE EMMC PIN

ISP INFO READ EMMC PROGRAMMER TNM5000 READ EMMC BOARD HK.T.RT2841P831 SUNNY 18AT027

Programmer ISP Cable EMMC pin
ISP PIN 1 CMD
ISP PIN 3 RST-n(Reset) (mandatory)
ISP PIN 5 CLK (Clock)
ISP PIN 6 DAT0
ISP PIN 8, 10 VSS (GND)
Vcc of Chip Must be ON. Reset is needed only when circuit reset is not working.

Note 1: After Selecting EMMC, programmer will be switched to Report view.
because EMMC files are too large and can’t be viewed by hex editor.
you can switch back to hex editor by unmarking the report button
.

Note 2: Load & Save buttons has no use in EMMC nand. you must select filename
after pressing read or program buttons. File will be saved automatically with
Boot 1, Boot 2, RPMB, EXT_CSD extensions for different parts of the chip.

Note 3: After pressing read or Program, EMMC size and type will automatically
be Detected

Note 4Use Config Window for selecting Different Parts of the chip for read and write.
Also, chip Size and name is read from the chip and can be viewed in this window.

Note 5: Erase is for total chip erase. before Programming Each part, Programmer
will erase it automatically, so no need for chip erase before program.

Note 6: Only First 192 byte of EXT_CSD is writable by users and Some of these bytes
are read-only and some parts are one-time programable so if you write over these areas,
you get Write error.

Note 7: in most cases, Reset Pin is not necessory, Power on/off the device for reset


to see EMMC pinout photo as well as to download EMMC BIN Firmware. you must subscribe

PROGRAMMER RT809H PIN ISP READ EMMC

PROGRAMMER RT809H PIN ISP READ EMMC H26M41204HPR

crystal 27.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC 1

crystal 27.000 MHz PINS 1 and 2 connect with GND. tv must be in 220v plug. and read EMMC. no need for extra voltage. 3.3v and 1.8v. for reading EMMC

LG LC490DUY SHA1

PANEL LG LC490DUY-SHA1


SUNNY MODEL SN49DLK27-0216


BOARD HK.T.RT2841P831 SUNNY 18AT027


EMMC H26M41204HPR FIRMWARE


PANEL LG LC490DUY-SHA1


READ EMMC PROGRAMMER TNM5000



repairalltv.com